All

A useful magnet can sit on a fridge door for a long time, which is why plumbers, pizza shops and realtors still hand them out. Ours are printed with your artwork in four square sizes and sold in runs from 50 to 10,000. Sizes:...

Coroplast is corrugated plastic, the light, rigid board you see on lawns during election season and outside open houses. Our signs are 18" x 24", the standard yard sign size, and you choose whether the print goes on one side or both. Size: 18"...

Not sure which transfers or supplies someone needs? Let them choose. A Smash Transfers gift card can go toward DTF transfers, gang sheets, heat press tools and embroidery supplies. $10 $25 $50 $100 $250 $500 It makes a practical gift for someone starting a...

Crooked prints usually come from eyeballing the placement. An alignment ruler gives you a fixed reference, so the transfer goes on straight and in the same spot on every garment. The usual routine is simple. Lay the shirt flat on the press, find the...

This listing is for a Barudan K-Series multihead embroidery machine with 8 heads. A multihead machine stitches the same design on several garments at the same time, one per head, which is how embroidery shops take on team orders and corporate runs without running...

Thread snips are the tool you reach for constantly at an embroidery machine. They trim jump stitches, thread tails and loose ends quickly, without the full open-and-close of a pair of scissors. These measure 4.9 inches, a size that sits comfortably in the hand...

Every embroiderer has stitched something that had to come out. A seam ripper makes that job manageable: the point slides under a stitch, and the blade in the curve cuts it without tearing the fabric around it. This compact tool works as both a...

Small embroidery scissors are for the cuts big shears can't make: trimming a thread right against the stitching, clipping inside a tight shape, or tidying the back of a design. These are 3.6 inches long and made of stainless steel. The crane design is...

Size 75/11 is the needle most machine embroidery runs on, because it pairs with standard #40 thread. Smash Tiger needles in this size come 100 to a pack and are titanium. A hundred needles goes a long way on a single-head machine and makes...

Tear away backing supports the fabric while it's being stitched, then tears off cleanly once the design is done. It's the usual choice for stable fabrics that won't stretch out of shape later, such as caps, towels, canvas and many woven shirts. This is...

3D puff embroidery is stitched over a layer of foam, which lifts the satin stitches off the garment and gives the design its raised look. This sheet is Smash Puff foam in yellow, 3mm thick and 24 by 36 inches. Match the foam to...

White foam is the one to keep on hand for white lettering on dark caps. This is Smash Puff 3D foam in white, 3mm thick, in a 24-inch by 36-inch sheet. Use white under white, cream, silver and pale thread colors. Under a dark...

Red is a team color, a school color and a brand color for a lot of the caps that come through embroidery shops. This Smash Puff foam in red lets you raise those designs with foam that matches the thread. The sheet is 3mm...

When the thread is blue, the foam under it should be blue too. This sheet of Smash Puff 3D foam is blue, 3mm thick and 24 by 36 inches, for raised embroidery in royal, navy and other blue shades. Puff works best on structured...

Black foam goes under black and other dark threads, from charcoal to deep navy. If you stitch a black logo over white foam, the white can show between the stitches; over black foam it disappears. You get a single 24" x 36" sheet of...

Smash Film Laminate is a polyurethane film supplied on a roll 19 inches wide and 50 yards long. A roll that size is meant for shops that use laminate film regularly in their finishing work, rather than for a single project. Embroidery and patch...

Cut away backing stays in the garment after you stitch. You trim the excess around the design, and what's left keeps supporting the embroidery through wear and washing. That makes it the go-to backing for fabrics that stretch, like T-shirts, polos, fleece and performance...

Left-chest logos on polos and T-shirts are usually stitched on cut away backing, and a 9-inch square covers the hoops most of them need. That's the job these are for. The pack holds 250 pre-cut squares of white 3 oz cut away, so the...

Pre-wound bobbins save your operators from winding their own, and a sideless bobbin has no plastic or cardboard sides, so the thread sits straight in the bobbin case. This box holds 144 white Smash sideless bobbins, size L, with 150 yards on each. White...

On a black hoodie or a navy cap, white bobbin thread can show at the edges of a design. Black bobbins avoid that. These Smash sideless bobbins are wound with black polyester filament, size L, with 150 yards per bobbin and 144 bobbins in...